| Items | Specs |
| Function | Digital display work, wireless remote control start and close studs |
| Effective Interception Distance | 6-15meters(in options) |
| Puncture Tire Thickness | ≤35mm |
| Max weight capacity | 20T |
| Remote control speed | ≤ 1 time / sec |
| Remote control distance | 45meters (Empty zone) |
| Spike Barrier Weight | 16 kgs |
| Standard Spike Barrier Size | 6000(L)*240(W)*30(H)mm |
| Working Voltage | 12V |
| Venting Hollow Steel Needle Size | φ5mm×43mm |
| Packing box size | 630(L)*610(W)*280(H)mm |
| Gross weight(6m) | 34 kgs |
Using Instruction:
1. Before using, ensure that the battery in the remote control box
is charged for a sufficient time to keep the voltage of the power
supply between 11V and 13.5V.
2. Open the right side cover of the roadblock box, roll out the
roadblock roll, remove the elastic hook for fixing the roadblock,
lean on the side of the roadside, and roll to the road to intercept
the vehicle.
3. Connect the wiring between the remote control box and the
roadblock. Insert one end of the two-meter three-core connection
cable into the roadblock connection jack and the other end into the
three-core connection jack of the remote control box.
4. Open the top cover of the remote control box, pull the power
switch to the built-in power supply, the power indicator light is
on, the device enters the working state, and the left receiving
antenna is pulled out to increase the receiving distance.
5. When it is necessary to perform the task of intercepting the
suspect vehicle, press the large button on remote control key, and
the stainless steel hollow needle in the roadblock is automatically
erected. At this time, if the roadblock is forcibly passed, the
wheel will be pierced into several stainless steel hollow needles.
The tire deflated immediately within two seconds and could not
continue driving.
6. After the interception task is finished, press the small button
on the remote control key, and the stainless steel hollow needle
that is erected will rotate back to the original position and enter
the standby state.
7. Recycling of the remote control roadblock, after the roadblock
is rounded, fix the roadblock with the elastic hook strap, turn off
the remote control box power switch, and put the remote control box
into the middle of the roadblock, and hold the roadblock in the
left hand, right hand rolling barrier block into the box, put in
the connection cable and buckle the cover.
8. The remote control roadblock is also equipped with an external
power connection. When the power supply voltage in the remote
control box is insufficient and cannot work normally, one end of
the 15M connection cable can be inserted into the
external power connection jack of the remote control box, and the
other end is inserted into the 12V car point. To the cigarette
lighter jack, pull the power switch of the remote control box to
the external power supply position, and the operation is the same
as the above.
9, work indicator
(1) Power indicator light - When the remote roadblock needs to
perform the interception task, turn on the power switch in the
remote control box, and the power indicator light is on.
(2) Undervoltage indicator light——When the undervoltage of the
power supply in the remote control box is lower than 11V, the
undervoltage indicator light is on, and it needs to be charged at
this time. The charging indicator lights up when charging, and the
charging time is 8-12 hours.
(3) When the red work light remote control stop road barrier is in
the working state of interception, the two red indications above
the remote control box are on, the interception task ends, the
power is turned off, and the indicator light stops working.
Related Products:
Under Vehicle Inspection System SPV3300:
Under vehicle surveillance system mainly adopt to inspect the
beneath part of a variety of vehicles.
It can quickly and accurately identify threats/ contraband/
smuggling of persons hiding at the bottom.
UVSS greatly improved vehicle safety inspection speed and accuracy,
reduce investment in human resources.
